BENCHMARK DAC1 MANUAL PDF

BENCHMARK DAC1 MANUAL PDF

DAC1 USB Instruction Manual. Revision G. Page 6. Overview. The DAC1 USB is a reference-quality, 2- channel kHz bit digital-to-analog audio converter. View and Download Benchmark DAC1 instruction manual online. 2-Channel bit kHz Audio Digital-to-Analog. DAC1 Media Converter pdf manual. View and Download Benchmark DAC1 instruction manual online. 2-Channel bit 96 kHz Audio Digital-to-Analog Converter. DAC1 Media Converter pdf.

Author: Tojakus Kigajin
Country: Cape Verde
Language: English (Spanish)
Genre: Software
Published (Last): 11 April 2016
Pages: 231
PDF File Size: 2.41 Mb
ePub File Size: 4.22 Mb
ISBN: 294-5-31576-179-4
Downloads: 3494
Price: Free* [*Free Regsitration Required]
Uploader: Dubei

These inputs are selected from a front-panel toggle switch. Page 27 20 Hz to 20 kHz is very slight. If the failure benchmatk been caused by misuse, neglect, accident or abnormal operating conditions, repairs will be billed at the normal shop rate. Page 35 We set the interface jitter amplitude to its maximum value of DAC1 performance did not change when the jitter was turned off.

BENCHMARK DAC1 INSTRUCTION MANUAL Pdf Download.

Table of Contents Add to my manuals Add. Low-noise Internal Power Supply Frequency Response Tests Page 17 Benchmark Media Systems, Inc. Static discharge may cause component failures, may affect the long-term reliability, or may degrade the audio performance.

  BSNL PREPAID PLANS IN MAHARASHTRA PDF

Hpa2 Tm Headphone Outputs The above graph demonstrates that the DAC1 is free from idle tones and clock crosstalk. Page 28 kHz. Jumper Settings A 2-pin jumper on header P2 see Photo 1 can be used to disable the front-panel source-selection switch.

If the failure has been caused by misuse, neglect, accident, or, abnormal operating conditions, repairs will be billed at the normal shop rate.

Enter text from picture: Rack mount kit blank panel, junction block, and rack-mount screws: Volume Control Curve The above graph shows the differential phase between 10 audio channels bencchmark 5 DAC1 converters.

Benchmark DAC1 PRE Manuals

The minor variations in the above plots are due to measurement limitations. Group Delay latency For continued fire hazard protection, fuses should be replaced ONLY da1 the exact value and type as indicated on the rear panel.

Practitioners of Digital Audio need to understand these effects. The DAC1 contains static sensitive components and should only be opened by qualified technicians. Page 23 Benchmark Media Systems, Inc.

Benchmark DAC1 PRE Manuals

One pair of 8-pin headers controls the output level at each XLR jack as follows: The highest non-line related tone measures — dBFS. In such an application, the digital source selection can be made using the jumper on dav1 P2.

  G2R-2 12VDC PDF

Ac Power-entry And Fuse Module We set the interface jitter amplitude to its maximum value of Page 19 of Distortion should still be well masked at higher playback levels. Compare this to the performance of the balanced outputs see previous graph. Page 33 Benchmark Media Systems, ,anual. Do not attempt to remove the faceplate or rear panel. The Volume this manual. Low-impedance Passive Pads Page of 51 Go. To print the manual completely, please, download it. Table of Contents Add to my manuals Add.

Page 28 Benchmark Media Systems, Inc.

It is therefor important to attack jitter at both ends of the audio chain. Page 36 Coaxial Digital Input Sensitivity Manuzl above graph shows that the performance of the DAC1 is not a function of the signal level at the coaxial digital input.

Jumper Settings A 2-pin jumper on header P2 see Photo 1 can be used to disable the front-panel source-selection switch.