AUDIOVOX CCS-100 MANUAL PDF

AUDIOVOX CCS-100 MANUAL PDF

Follow the instructions in the CCS Manual. Using the VSS signal on a standard (manual) transmission vehicles Murphs CCS and the original Audiovox. only, and is not intended to replace the CCS Installation Manual. Manual, for those persons that choose to install the CCS cruise. Auto and car manuals and free pdf automotive manual instructions. Find the user manual Audiovox CCS Automobile Accessories User Manual. Page 1.

Author: Bagor Zurg
Country: Romania
Language: English (Spanish)
Genre: Life
Published (Last): 5 September 2009
Pages: 170
PDF File Size: 13.92 Mb
ePub File Size: 5.25 Mb
ISBN: 170-7-52532-111-7
Downloads: 52750
Price: Free* [*Free Regsitration Required]
Uploader: Jucage

Audiovox CCS-100 Automobile Accessories User Manual

It is extremely important that the throttle can not stick when the cruise control throttle connection is added. Wiring Routing the Main Wiring Harness 1. Routing the Main Wiring Harness 1. The Red Led should go out when you release the brakes. Attach the cruise control cable so that it parallels the existing throttle cable as nearly as possible. Locate your vehicle by make, model, and engine size in the included Reference Manual in order to identify the location of the VSS and Tach connection locations.

The engine will not rev up this way as you shift. Control Switch Installation Figure 1 Carefully cut-out along dotted lines and place on selected area. A simple Google search might find online instructions already posted on your vehicle.

Loosely wrap the wire to hold it in place. Turn on the cruise at the Cruise Control Keypad. Spread the slots in the small Bead chain eyelet connector Part Number 25 and bead chain coupling Part Number 24 before installing them.

Audiovox Automobile Accessories CCS User Guide |

If you already have a SPDT relay in the brake circuit, either you have the wrong relay or auxiovox have it connected wrong.

While rotating the shaft, carefully auduovox one wire into one set of magnet slots. If you are installing the audiovlx to a motorcycle, determine where you are mounting the cruise control keypad. Switched power is a circuit that is on only when manhal ignition key is turned on. Check for a good connection at your Tachometer source. The orange and gray wire from the cruise control keypad needs to be connected manuual switched power. The Rostra needs both signals to operate.

  KATHY SIERRA SCJP EBOOK PDF

The orange and gray wires from the Cruise Control keypad are connected here The wire on the rear brake switch that normally has 0 Volts DC and then 12 Volts DC when you apply either the front or rear brakes. The Cruise Module makes “decisions” based upon speed,tachometer, and brake signal information.

You want just a little slack at idle in the cruise control servo cable closed throttle position but you must have enough slack that the throttle is fully closed. You need to know the wire colors of the following: Got it, continue to print.

Brake Wire Connection Test: If you are using Tach only for your signal source, remember to pull the Black jumper to the left of the Dip switches inside the servo. If your make and model cannot be located, then the Magnet Kit must be installed. The more vacuum the better.

Page 3 The Cruise Module makes “decisions” based upon speed,tachometer, and brake signal information. Also test that the cruise shuts off with the audiovoz pulled in The engine will rev up RPM before the cruise shuts off. The negative terminal of the coil wire color or the vehicle tachometer wire color.

Audiovox CCS-100 Installation Manual

You can use any circuit including accessory leads or the wire running to your taillights not brake lights. Rearview audiovoox with 4″ color lcd monitor and camera package v2. Murphs CCS controls engine speeds using a tachometer signal and engine vacuum to control vehicle speed. The keypad supplied with the cruise is a normally closed switch. By pressing ‘print’ button you will print only current page.

  DESHOJANDO MARGARITAS WALTER RISO DESCARGAR PDF

Seal off the end off the vacuum line to the engine with you finger. The Purple Servo wire must be connected to chassis ground for the Cruise to turn on. Sirs, I have a street manuak project that I am installing your cruise control on, thus far I have not been able ccz-100 get it to work.

Usually but not always you want to route the cruise servo cable to follow the motorcycles original throttle opening cable. We suggest you buy one when you get your cruise control to use at least temporally for initial testing. The gray wire is illumination light for the cruise control keypad. Be sure to load the wires according to the color coded label on the connector, and press the terminals in fully until a audiovpx is heard.

AUDIOVOX CCS INSTALLATION MANUAL Pdf Download.

Note that acceleration in the lower gears with the cruise on can be quite strong. The mankal taillight brake wire color of Blue with a Red Stripe before the connector and solid Blue after the connector is for a Kawasaki C14 only.

audiovos For automobiles, you can use any vacuum source with the exception of the vacuum line running to your power brake booster. If you are doing an installation on a motorcycle or standard transmission automobile without the benefit of following written instructions for your vehicle, start with these settings: When you press on either brake the Red LED should be continuously lit.

Speed Sensor Installation Step 6: Do you feel suction?