14mz, Instruction manual • Read online or download PDF • Futaba 14MZ User Manual. Get Futaba 14MZ Manual. Get all Futaba manuals! 14MZ. 14 CHANNEL RADIO CONTROL SYSTEM. PCMG3/PCM/FM selectable. INSTRUCTION. Compact Flash (CF) Card Handling Instructions Follow these precautions when handling the CF card included in your 14MZ transmitter. DO NOT allow the.
|Published (Last):||22 March 2016|
|PDF File Size:||13.4 Mb|
|ePub File Size:||15.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
When pitch trim is used, a curve with same setting contents at other mankal, perform pitch trim adjustment added is also displayed. Sound Sound Sound recording and playback.
You can listen to them through the built-in speaker or a headphone by the earphone plug.
Internet access is available at no charge at most public libraries, schools, and other public resources. Although you may notice the flickering of the numbers on the LCD screen, this is not an abnormal, because the LCD screen is frequently refreshing those even if those numbers are 14zm.
Starts and sets the trainer system. You can always monitor trim positions by graphics on the screen. Model Name The model name that is currently used is displayed here.
This volume is digital type rotary encoder. Always hold the CF card by the edges during installation and removal.
Airplane, general This function selects manuql switch and rate adjustment of each rudder, ailerons, elevators, or flaps when a snap roll is performed. Perform this setting when you purchase the set and when adjustment is necessary.
What’s missing? Tell us about it.
Modification, adjustment, and replacement of parts: Push the area that shows the frequency in the home screen or push the “Frequency” button in the Linkage menu. If you continue pressing it, the trim position starts to move faster.
Mount the battery and then slide the battery in the direction shown in the figure until you hear a locking sound.
Be sure that all channels work correctly in both transmitters before flying. The method of applying to call the curve setup screen, and then correct the clockwise or counterclockwise torque when slowing. Use the Model Type function in the Linkage Menu to select the swash type matched to the fuselage beforehand. Do not use any other chargers except CR that is for 12V application to charge the LT2F battery through this connector. To prevent possible damage to your radio gear, turn the power switches on and off in the proper manal The differential rate can also be adjusted according to the flying msnual by setting a fine tuning VR.
For a detailed description of majual selection method, 1. When you have a problem of saving or reading data such as picture data after a long period of use, please get a new CF card. Close the card cover and slide it to the original position.
FUTABA 14MZ INSTRUCTION MANUAL Pdf Download.
Select the setting mode. Touch the function button of the dual rate number to be assigned. Install the Futaba FX40 test program.
In order for you to make the best use of your system and to fly safely, please read this manual carefully. Page 10 Stick Each axis is supported by dual ball bearings. Mixes Program mixing which can be freely customized.
For safety reasons, the radio will be emmiting only after you push the confirmation button when turning on the power. Use the adjustment buttons to set the rate.
Page 83 Flap setting [Corresponding model type]: The product is subject to regulations of the FCC and is restricted under United States law to such purposes. As the internal circuit of the transmitter stays on the standby mode for 4 hours after turning off the power, some part of the circuit is consuming current. Push the user’s name. Touch the button of the rate or EXP curve rate your want to set.
It is also recommended to charge the battery just before your usage. The T14MZ is designed so that the airplane This section describes the AFR, program mixing, and glider including EP glider model types are and other functions common to all model types. Servo connection by model type The T14MZ transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage 14ma.
It raises the elevators to correct for drooping of the nose during airbrake operation. Receiver and servos connection Connect the receiver and servos in accordance with the connection diagram shown below. If you would like, on the function- work simultaneously. The operation speed In Speed and the return speed Out Speed can be set individually. Servo Grouping With the 14MZ, you can group multiple servos that control kanual single function onto one transmitter operation — but plug the servos themselves into different individually adjustable receiver channels even non-consecutively without needing a separate servo synchronizer for mixing.
A curve setting example is shown 14ma.